Abstract: What could be more basic than a voltage reference - a simple, constant reference voltage? As is all design topics, there are tradeoffs. This article discusses the different types of voltage references, their key specifications,and the design tradeoffs, including accuracy, temperature-independence, current drive
capbility, power dissipation, stability, noise, and cost.
You can find voltage references inside almost any advanced electronic product, either standalone or integrated into larger functions. For example:
- In a data converter, a reference provides an absolute voltage to compare to the input voltage to determine the proper digital code.
- In a voltage regulator, a reference provides a known value which is compared to the output to develop the feedback that is used to regulate the output voltage.
- In a voltage detector circuit, the reference is used as an absolute threshold to set the trip point.
The required specifications depend on the application. This article discusses the different types of voltage references, their key specifications,and design tradeoffs. It offers information to help designers select the optimum voltage reference for their applications.
The Ideal
An ideal voltage reference would have a perfect initial accuracy and maintain its voltage independent of changes in load current, temperature, and time. In the real world, a designer must make tradeoffs such as: Initial Voltage Accuracy, Voltage Temperature Drift and Hysteresis, Current Source and Sink capability, Quiescent Current (or Power Dissipation), Long Term Stability, Noise, and Cost.
Types of Reference
The two most common types of references are Zener and Bandgap. Zeners are usually used in two-terminal shunt topologies. Bandgap references are usually used in three-terminal Series topologies.
Zener Diodes and Shunt Topologies
Zener diodes are diodes optimized for operation in the reverse-bias breakdown region. Because breakdown is relatively constant, it can be used to generate a stable reference by driving a known current in the reverse direction.
One big advantage of zeners is the wide range of voltages that are available, from 2V up to 200V. They also have a wide range of power handling capability, from several milliwatts to several watts.
The key disadvantages of zener diodes is that they are not precise enough for high-precision applications and their power consumption makes them a tough fit for low-power applications. An example is the BZX84C2V7LT1, which has a breakdown, or nominal reference voltage, of 2.5V with a variation from 2.3V to 2.7V, or +/-8% accuracy. This is suitable only for applications that need little precision.
An additional concern with a zener reference is the output impedance. Our example above has an internal impedance of 100 at 5mA and 600 at 1mA. A non-zero impedance will cause an additional variation in the reference voltage depending on the variation in load current. Selecting a zener with low output impedance minimizes this effect.
Buried zener diodes are a specific type of zener that are more stable that a regular zener, due to their structure which places them below the surface of the silicon.
An alternative to an actual zener diode is an active circuit that emulates a zener. Circuitry allows the device to significantly improve upon the classic limitations of the zener. One such device is the MAX6330. It has a tight 1.5% (max) initial accuracy over a 100uA to 50mA variation in load. A typical implementation of this type of IC is shown in Figure 1.
Figure 1.
Selecting the Proper Shunt Resistor
All shunt configuration references need a current limiting resistor in series with the reference element. It can be calculated from the following equation:
RS = (VIN(max)-VSHUNT(min)) / (ISHUNT(max)+ ILOAD(min)) < RS < (VIN(min) -VSHUNT(max)) / (ISHUNT(min) + ILOAD(max))
Where:
VIN is the input voltage range
VSHUNT is the regulated voltage
ILOAD is the output current range
ISHUNT is the minimum shunt operating current
Note that a shunt circuit will always consume ILOAD(max) + ISHUNT whether or not a load is present.
The same shunt can be used for 10Vin or 100Vin by properly sizing RS. Choosing the largest nominal resistor value for RS gives the lowest current consumption. Remember to provide a safety margin to incorporate the worst-case tolerance of the resistor used. You should also ensure that the resistor's power rating is adequate, using either of the following two general power equations:
PR = IIN(VIN(max) - VSHUNT)
= I2INRS
= (VIN(max) - VSHUNT)2/RS
Bandgap References and Series Mode Topologies
The key differences between a shunt and series reference is that the three terminal series-mode voltage references do not require an external resistor and have significantly lower quiescent power. The most common form is the ubiquitous bandgap reference.
Bandgap Basics
A bandgap reference develops two voltages: One has a positive temperature coefficient (tempco) and one has a negative tempco. Together, they have a zero-tempco sum at the output.
The positive tempco is usually derived from the difference of two Vbe's running at different current levels. The negative tempco uses the naturally negative tempco of the Vbe voltage (see Figure 2).
In practice, the tempco sum is not exactly zero. Depending on design details like the IC circuit design, packaging, and manufacturing test capabilities, these devices can usually achieve a Vout tempcos between 5 and 100ppm per degree C.
Figure 2. Bandgap voltage reference.
The use of either a shunt or series topology is typically dictated by the application and the desired performance. Please refer to Table 2 for some comparisons between zeners in shunt topologies and bandgaps in series topologies.
Table 1. Voltage Reference Comparison Guide
| What |
Zener - Shunt Topology |
Buried Zener - Shunt Topology |
Band-Gap - Series Topology |
| Pro's |
Wide/high Vin capable
Best for non-power critical applications due to higher Iquiescent (1-10mA)
>1% FS initial Accy. |
Wide/high Vin capable
Best for non-power critical applications due to higher Iquiescent (1-10mA)
0.01% to 0.1% FS Initial Accy |
Typically lower Vin range
Low Quiescent current(uA to ~1mA)
No ext resistor
Lower Iquiescent
0.05% to 1% FS initial Accy
Low dropout voltages |
| Con's |
Current is always used
Requires external resistor
Lower precision
Can only sink current
High dropout voltage |
Higher Iquiescent than bandgaps |
Limited Vin range
Pass element losses |
| Gotcha's |
Long-Term stability |
Not all Series devices sink current |
Not all Series devices sink current |
System Design Issues and Reference Selection
Power Consumption
If you are designing a medium precision system like a high-efficiency, +/-5% power supply or perhaps an 8-bit data acquisition system that requires minimal power, you could use a device like the MAX6025 or MAX6192. Both are 2.5V references that consume a maximum of 35uA. They have very low output impedance so the reference voltage will be virtually independent of IOUT.
Source and Sink Current
Another specification is the reference's ability to source and sink current.
Most applications require a voltage reference to source current to the load(s) and of course, the reference needs to be able to supply the required load current. It also needs to supply any Ibias or leakage currents -- their sum can sometimes exceed the load currents.
ADCs and DACs typically require between tens of micro-amps for a converter like the MAX1110, to 10mA(max) for devices like the AD7886. The MAX6101-5 family of references sources 5mA and sinks 2mA. For really heavy loads, the MAX6225/41/50 family will source and sink 15mA.
Temperature Drift
Temperature drift is normally a correctable parameter. It is typically a very repeatable error. Correction can be accomplished by adding a calibration step or by reading a value from a look up function that has been previously characterized.
Calibration is very common in high-resolution systems. In a 16-bit system - you will need better than a 1ppm/C reference for the commercial (0C to 70C) temperature range to stay within the +/-1LSB over the entire range, with a 25C reference point.  V = (1ppm/C * 5V * 45C) = 255uV. This same temperature drift extended over the industrial temperature range would only be acceptable for a 14-bit system.
Noise
Noise usually consists of random thermal noise, but can also include flicker noise and other spurious sources. The MAX6150, MAX6250 and MAX6350 are all good choices for low noise applications with 35uV, 3uV and 3uVp-p noise performance respectively. All of these will contribute less than 1LSB of noise into your measurement. One could over-sample and average, but it comes at the cost of processor power and increased system complexity and cost.
Output Voltage Temperature Hysteresis
This parameter is defined as the change in output voltage at the reference temperature (25C) due to sequential but opposite temperature excursions (i.e.: hot-to-cold and then cold-to-hot). Very negative effects can occur due to this effect since its amplitude is directly proportional to the temperature excursion the system underwent. In many systems this type of error is not very repeatable. This parameter is a function of design of the IC circuit as well as effects from the packaging. For example: The MAX6001 type device in a 3-pin SOT23 has a typical Temperature Hysteresis of 130ppm. But a larger, more stable package, like the MAX6190 in the SO-8, has only 75ppm.
Long Term Stability
This parameter is defined as a change in voltage over time. It is primarily due to die stress or perhaps ion migration that exists in a package or family of devices. It is important to note that the circuit board cleanliness can show up as a long-term change over time; especially over temperature and humidity. This effect, at times can be larger than the inherent device stability. Long-term stability is typically only specified at the reference temperature, usually 25C.
Summary
The difficulties of designing any system lie in balancing the trade-offs: Cost, size, precision, power consumption, etc. It is important to consider all of the pertinent parameters when selecting the optimum reference for a design. It is interesting to note that many times a more expensive component can result in a lower total system cost due to the reduction in cost of compensation/calibration in manufacturing phase.
Table 2. Abbreviated list of MAXIM Voltage References
| Part
Number |
Output
Voltage
(V) |
Supply
Voltage
Range
(V) |
Temp. Drift
(ppm/°C
max) |
Initial Accuracy
TA=+25°C
(% F.S. max) |
Quiescent
Current
(mA max) |
0.1Hz to 10Hz
Noise(µVp-p),
max (typ) |
Package
Options |
Temp.
Ranges* |
| MAX6160 | Adj.(1.23 to 12.4) | 2.7 to 12.6 | 100 | 1 | 100µA | (15) | SOT143, SO | E |
| MAX6120 | 1.2 | 2.4 to 11 | 100 | 1 | 70µA | (10) | SOT23, SO | E |
| MAX6520 | 1.2 | 2.4 to 12.6 | 50 | 1 | 70µA | (10) | SOT23, SO | E |
| MAX6001 | 1.25 | 2.5 to 12.6 | 100 | 1 | 45µA | 25 | SOT23 | E
|
| MAX6012 | 1.25 | 2.5 to 12.6 | 20 to 30 | 0.3 to 0.5 | 35µA | 25 | SOT23 | E
|
| MAX6190 | 1.25 | 2.5 to 12.6 | 5 to 25 | 0.16 to 0.48 | 35µA | 25 | SO | E
|
| MAX6021 | 2.048 | 2.5 to 12.6 | 20 to 30 | 0.2 to 0.4 | 35µA | 40 | SOT23 | E
|
| MAX6191 | 2.048 | 2.5 to 12.6 | 5 to 25 | 0.1 to 0.5 | 35µA | 40 | SO | E
|
| MAX872 | 2.5 | 2.7 to 20 | 40 | 0.2 | 10µA | (60) | DIP, SO | C, E
|
| MAX873 | 2.5 | 4.5 to 18 | 7 to 20 | 0.06 to 0.1 | 28µA | (16) | DIP, SO | C, E
|
| MAX6002 | 2.5 | 2.7 to 12.6 | 100 | 1 | 45µA | 60 | SOT23 | E
|
| MAX6025 | 2.5 | 2.7 to 12.6 | 20 to 30 | 0.2 to 0.4 | 35µA | 60 | SOT23 | E
|
| MAX6125 | 2.5 | 2.7 to 12.6 | 50 | 1 | 100µA | (15) | SOT23, SO | E
|
| MAX6192 | 2.5 | 2.7 to 12.6 | 5 to 25 | 0.1 to 0.4 | 35µA | 60 | SO | E
|
| MAX6225 | 2.5 | 8 to 36 | 2 to 5 | 0.04 to 0.1 | 2.7 | (1.5) | DIP, SO | C, E
|
| MAX6325 | 2.5 | 8 to 36 | 1 to 2.5 | 0.04 | 2.7 | (1.5) | DIP, SO | C, E
|
| MAX6003 | 3 | 3.2 to 12.6 | 100 | 1 | 45µA | 75 | SOT23 | E
|
| MAX6030 | 3 | 3.2 to 12.6 | 20 to 30 | 0.2 to 0.4 | 35µA | 75 | SOT23 | E
|
| MAX6193 | 3 | 3.2 to 12.6 | 5 to 25 | 0.07 to 0.33 | 35µA | 75 | SO | E
|
| MAX874 | 4.096 | 4.3 to 20 | 40 | 0.2 | 10µA | (60) | DIP, SO | C, E
|
| MAX6004 | 4.096 | 4.3 to 12.6 | 100 | 1 | 45µA | 100 | SOT23 | E
|
| MAX6041 | 4.096 | 4.3 to 12.6 | 20 to 30 | 0.2 to 0.4 | 35µA | 100 | SOT23 | E
|
| MAX6141 | 4.096 | 4.3 to 12.6 | 50 | 1 | 105µA | (25) | SOT23, SO | E
|
| MAX6198 | 4.096 | 4.3 to 12.6 | 5 to 25 | 0.05 to 0.24 | 35µA | 100 | SO | E
|
| MAX6241 | 4.096 | 8 to 36 | 2 to 5 | 0.025 to 0.1 | 2.9 | (2.4) | DIP, SO | C, E
|
| MAX6341 | 4.096 | 8 to 36 | 1 to 2.5 | 0.025 | 2.9 | (1.5) | DIP, SO | C, E
|
| MAX6045 | 4.5 | 4.7 to 12.6 | 20 to 30 | 0.2 to 0.4 | 35µA | 110 | SOT23 | E
|
| MAX6145 | 4.5 | 4.7 to 12.6 | 50 | 1 | 105µA | (30) | SOT23, SO | E
|
| MAX6194 | 4.5 | 4.7 to 12.6 | 5 to 25 | 0.04 to 0.22 | 35µA | 110 | SO | E
|
| MAX675 | 5 | 8 to 33 | 12 to 20 | 0.15 | 1.4 | 15 | TO-99, DIP, SO | C, E
|
| MAX875 | 5 | 7 to 18 | 7 to 20 | 0.06 to 0.1 | 0.28 | (32) | DIP, SO | C, E
|
| MAX6005 | 5 | 5.2 to 12.6 | 100 | 1 | 45µA | 120 | SOT23 | E
|
| MAX6050 | 5 | 5.2 to 12.6 | 20 to 30 | 0.2 to 0.4 | 35µA | 120 | SOT23 | E
|
| MAX6150 | 5 | 5.2 to 12.6 | 50 | 1 | 110µA | (35) | SOT23, SO | E
|
| MAX6195 | 5 | 5.2 to 12.6 | 5 to 25 | 0.04 to 0.2 | 35µA | 120 | SO | E
|
| MAX6250 | 5 | 8 to 36 | 2 to 5 | 0.02 to 0.1 | 3 | (3) | DIP, SO | C, E
|
| MAX6350 | 5 | 8 to 36 | 1 to 2.5 | 0.02 | 3 | (1.5) | DIP, SO | C, E
|
| REF02 | 5 | 8 to 33 | 8.5 to 250 | 0.3 to 2 | 1.4 | 15 | TO-99, DIP, SO | C |
* Temperature Ranges: C = 0°C to +70°C, E = -40°C to 85°C
References
1) The Art of Electronics, by Paul Horowitz & Winfield Hill, Chapter 6
2) Micro-Electronic Circuits, by Adel S. Sedra & Kenneth C. Smith
フィードバックをお寄せください。
内容に満足されましたか、あるいは満足されていませんか？もっと良いページにできると思いますか？あるいは、単なるコメントでも結構です。フィードバックをお待ちしています。—マキシムはお客様からいただく訂正、提案を元に改善していきます。
このページを評価し、フィードバックを送信する。
自動アップデート
お客様が関心のある分野でアプリケーションノートが新規に掲載された際に自動通知Eメールの受信を希望する場合は、EE-Mail™にご登録ください。
| その他の情報 | |
APP 2879: Dec 29, 2003
|
| MAX6001 |
低コスト、低電力、低ドロップアウト電圧、3ピンSOT23電圧リファレンス |
フルデータシート
(PDF, 176kB)
|
無料
サンプル
|
| MAX6002 |
低コスト、低電力、低ドロップアウト電圧、3ピンSOT23電圧リファレンス |
フルデータシート
(PDF, 176kB)
|
無料
サンプル
|
| MAX6003 |
低コスト、低電力、低ドロップアウト電圧、3ピンSOT23電圧リファレンス |
フルデータシート
(PDF, 176kB)
|
無料
サンプル
|
| MAX6004 |
低コスト、低電力、低ドロップアウト電圧、3ピンSOT23電圧リファレンス |
フルデータシート
(PDF, 176kB)
|
無料
サンプル
|
| MAX6005 |
低コスト、低電力、低ドロップアウト電圧、3ピンSOT23電圧リファレンス |
フルデータシート
(PDF, 176kB)
|
無料
サンプル
|
| MAX6012 |
高精度、低電力、低ドロップアウト、3ピンSOT23、電圧リファレンス |
フルデータシート
(PDF, 192kB)
|
無料
サンプル
|
| MAX6021 |
高精度、低電力、低ドロップアウト、3ピンSOT23、電圧リファレンス |
フルデータシート
(PDF, 192kB)
|
無料
サンプル
|
| MAX6025 |
高精度、低電力、低ドロップアウト、3ピンSOT23、電圧リファレンス |
フルデータシート
(PDF, 192kB)
|
無料
サンプル
|
| MAX6030 |
高精度、低電力、低ドロップアウト、3ピンSOT23、電圧リファレンス |
フルデータシート
(PDF, 192kB)
|
無料
サンプル
|
| MAX6041 |
高精度、低電力、低ドロップアウト、3ピンSOT23、電圧リファレンス |
フルデータシート
(PDF, 192kB)
|
無料
サンプル
|
| MAX6045 |
高精度、低電力、低ドロップアウト、3ピンSOT23、電圧リファレンス |
フルデータシート
(PDF, 192kB)
|
無料
サンプル
|
| MAX6050 |
高精度、低電力、低ドロップアウト、3ピンSOT23、電圧リファレンス |
フルデータシート
(PDF, 192kB)
|
無料
サンプル
|
| MAX6120 |
低コスト、超低消費電力、高精度3端子、1.2V電圧リファレンス |
フルデータシート
(PDF, 176kB)
|
無料
サンプル
|
| MAX6125 |
SOT23、低コスト、低ドロップアウト、3端子電圧リファレンス |
フルデータシート
(PDF, 184kB)
|
無料
サンプル
|
| MAX6141 |
SOT23、低コスト、低ドロップアウト、3端子電圧リファレンス |
フルデータシート
(PDF, 184kB)
|
無料
サンプル
|
| MAX6145 |
SOT23、低コスト、低ドロップアウト、3端子電圧リファレンス |
フルデータシート
(PDF, 184kB)
|
無料
サンプル
|
| MAX6150 |
SOT23、低コスト、低ドロップアウト、3端子電圧リファレンス |
フルデータシート
(PDF, 184kB)
|
無料
サンプル
|
| MAX6160 |
SOT23、低コスト、低ドロップアウト、3端子電圧リファレンス |
フルデータシート
(PDF, 184kB)
|
無料
サンプル
|
| MAX6190 |
高精度、超低消費電力、低ドロップアウト電圧リファレンス |
フルデータシート
(PDF, 232kB)
|
無料
サンプル
|
| MAX6191 |
高精度、超低消費電力、低ドロップアウト電圧リファレンス |
フルデータシート
(PDF, 232kB)
|
無料
サンプル
|
| MAX6192 |
高精度、超低消費電力、低ドロップアウト電圧リファレンス |
フルデータシート
(PDF, 232kB)
|
無料
サンプル
|
| MAX6193 |
高精度、超低消費電力、低ドロップアウト電圧リファレンス |
フルデータシート
(PDF, 232kB)
|
無料
サンプル
|
| MAX6194 |
高精度、超低消費電力、低ドロップアウト電圧リファレンス |
フルデータシート
(PDF, 232kB)
|
無料
サンプル
|
| MAX6195 |
高精度、超低消費電力、低ドロップアウト電圧リファレンス |
フルデータシート
(PDF, 232kB)
|
無料
サンプル
|
| MAX6198 |
高精度、超低消費電力、低ドロップアウト電圧リファレンス |
フルデータシート
(PDF, 232kB)
|
無料
サンプル
|
| MAX6225 |
低ノイズ、+2.5V/+4.096V/+5V高精度電圧リファレンス |
フルデータシート
(PDF, 208kB)
|
無料
サンプル
|
| MAX6241 |
低ノイズ、+2.5V/+4.096V/+5V高精度電圧リファレンス |
フルデータシート
(PDF, 208kB)
|
無料
サンプル
|
| MAX6250 |
低ノイズ、+2.5V/+4.096V/+5V高精度電圧リファレンス |
フルデータシート
(PDF, 208kB)
|
無料
サンプル
|
| MAX6325 |
1ppm/℃、低ノイズ、+2.5V/+4.096V/+5V電圧リファレンス |
フルデータシート
(PDF, 216kB)
|
無料
サンプル
|
| MAX6341 |
1ppm/℃、低ノイズ、+2.5V/+4.096V/+5V電圧リファレンス |
フルデータシート
(PDF, 216kB)
|
無料
サンプル
|
| MAX6350 |
1ppm/℃、低ノイズ、+2.5V/+4.096V/+5V電圧リファレンス |
フルデータシート
(PDF, 216kB)
|
無料
サンプル
|
| MAX6520 |
50ppm/℃、SOT23、3端子、1.2V電圧リファレンス |
フルデータシート
(PDF, 92kB)
|
無料
サンプル
|
| MAX675 |
高精度、5V電圧リファレンス、MAX673の置換え |
フルデータシート
(PDF, 336kB)
|
無料
サンプル
|
| MAX872 |
10µA、低ドロップアウト、高精度電圧リファレンス |
フルデータシート
(PDF, 2.3MB)
|
|
| MAX873 |
低電力、低ドリフト、+2.5V/+5V/+10V高精度電圧リファレンス |
フルデータシート
(PDF, 444kB)
|
無料
サンプル
|
| MAX874 |
10µA、低ドロップアウト、高精度電圧リファレンス |
フルデータシート
(PDF, 2.3MB)
|
|
| MAX875 |
低電力、低ドリフト、+2.5V/+5V/+10V高精度電圧リファレンス |
フルデータシート
(PDF, 444kB)
|
無料
サンプル
|
| REF02 |
+5V、+10V、高精度電圧リファレンス |
フルデータシート
(PDF, 108kB)
|
無料
サンプル
|
|
|
 ダウンロード、PDFフォーマット (146kB)
AN2879,
AN 2879,
APP2879,
Appnote2879,
Appnote 2879
|
|
